Experimental Box Furnace with Temperature Between 1100 to 1300 Degree

Oriented by user needs, and based on product quality wholeheartedly provide users with quality square braided ceramic fiber rope, coors perforated ceramic alumina sheet, 12v ceramic heating element products! We provide all-round three-dimensional service for the new and old customers, so we are favored by the majority of customers. We grasp customer needs in real time, work closely with experts, accurately locate product needs, and continue to develop high-tech products. 'Creating quality products and striving for perfect service' is our tenet, and we wholeheartedly hope to have in-depth and wide-ranging cooperation with new and old customers. Facing the rapid economic development today, continuous innovation and perseverance are what we have always pursued, and your satisfaction and recognition are our expectations.

Product Description

The ceramic fiber module is a new type of refractory lining product introduced to simplify and speed up the construction of the kiln and improve the integrity of the lining.

Classification

Ceramic fiber modules can be divided into the following types according to the temperature grade

1050 ordinary ceramic fiber module

1260 standard ceramic fiber module

1260 high purity ceramic fiber module

1400 high aluminum ceramic fiber module

1400 Low Zirconium Ceramic Fiber Module

1400 Zirconium-containing ceramic fiber module

Properties

*White color, regular size

*Good fire resistance and heat insulation effect

Installation Steps

(1) Steel plate cleaning

Before the module is installed, the steel plate and furnace wall with the installation should be cleaned, and the rusty steel plate should be derusted.

(2) Pay off

When wiring, strictly follow the construction design drawing, take the center point of the module as the reference, wire to both sides, and mark the position of the bolts, try to make the position of the latter row of screws do not have large errors.

(3) Welding of anchors

The anchor nail is welded to the furnace wall steel plate, and the position should be accurate, and the error should be strictly controlled; the anchor nail must be perpendicular to the furnace wall during welding, and at the same time, try to avoid damage to the bolt thread. The deviation of the adjacent center distance of the bolts is ≤2, and the deviation of any two spacings is ≤ 3mm; After the welding is completed, hammering and bending are used to check the welding quality of the bolts one by one to ensure that the welding is firm, and then remove the welding slag.

(4) Backing blanket installation

First compress the ceramic fiber blanket to the required thickness, and spread the blanket and blanket in a staggered layer (the staggered amount is not less than the drawing requirements), and the quick card must be clamped to prevent rebound.

(5) Module installation

Take out the ceramic fiber module → screw the guide rod to the small end of the screw → pass the ceramic fiber module along the center hole through the guide rod to the furnace plate → use a special wrench to tighten the nut to the screw → unscrew the guide rod → proceed in sequence Installation of other ceramic fiber modules.

It should be noted that the module installation should follow the principle of first furnace top and then furnace wall, from bottom to top. After installing a row of modules, lay a compensation blanket on the cutting surface of the module (2 layers of 20mm blankets are extruded to a thickness of 25mm), and fix them on the installed module with U-shaped nails.

(6) Modular surface finishing

After the ceramic fiber module is installed, flatten the surface of the module with a wooden board to ensure that the module is squeezed tightly, and the large gaps are tightly filled with compensation blankets.

(7) Curing agent spraying

After the insulation layer is installed, in order to prolong the service life of the insulation cotton and enhance the ability to resist wind erosion and air erosion, a protective layer of curing agent should be sprayed on the surface of the module, with an amount of about 1.5kg/m2.

Q&A

1. What is the classification temperature?

The classification temperature is 1050-1400℃

2. What is the delivery sea port?

SHANGHAI, QINGDAO, TIANJIN or as per your request.

The modernization of Experimental Box Furnace with Temperature Between 1100 to 1300 Degree industry promoted by the company is guided by science and technology, using modern science and technology and industrialized production methods to comprehensively transform traditional and extensive industries, and gradually realize the industrialization, intensification and socialization of production methods, so as to conform to the development of contemporary economic society. Require. We strengthen mechanization, automation and informationization of production process to reduce human factors as much as possible. We spare no effort to improve product quality, continuously improve product technology, and ensure product leadership. At the same time, we also strive to provide customers with unparalleled high-quality services.

Hot Tags: ceramic fiber module, China, suppliers, manufacturers, factory, customized, wholesale, cheap, pricelist, low price, free sample, square braided ceramic fiber rope 5 8 50ft, nutec ceramic fiber modules, alumina ceramic grinding ball suppliers, ceramic fiber board manufacturers, Ceramic Fiber Tape, alumina oxide ceramic plate