1200 Degree Ceramic Fiber Heater Module

In the context of today's times, we are committed to developing green Silicon Nitride Tubes, hot water heater element, alumina ceramic data sheet in order to seize the market opportunities. The company has always regarded human resources as the first resource for enterprise development, and the construction of core talent group as the strategic core of development. Our company insists on subordinating the local interests to the overall interests, and takes safeguarding the interests of society and the country as the fundamental standard for testing the effectiveness of our work and corporate performance. Furthermore, the best and satisfaction service is a big surprise we give our clients!

Product Description

The ceramic fiber module is a new type of refractory lining product introduced to simplify and speed up the construction of the kiln and improve the integrity of the lining.

Classification

Ceramic fiber modules can be divided into the following types according to the temperature grade

1050 ordinary ceramic fiber module

1260 standard ceramic fiber module

1260 high purity ceramic fiber module

1400 high aluminum ceramic fiber module

1400 Low Zirconium Ceramic Fiber Module

1400 Zirconium-containing ceramic fiber module

Properties

*White color, regular size

*Good fire resistance and heat insulation effect

Installation Steps

(1) Steel plate cleaning

Before the module is installed, the steel plate and furnace wall with the installation should be cleaned, and the rusty steel plate should be derusted.

(2) Pay off

When wiring, strictly follow the construction design drawing, take the center point of the module as the reference, wire to both sides, and mark the position of the bolts, try to make the position of the latter row of screws do not have large errors.

(3) Welding of anchors

The anchor nail is welded to the furnace wall steel plate, and the position should be accurate, and the error should be strictly controlled; the anchor nail must be perpendicular to the furnace wall during welding, and at the same time, try to avoid damage to the bolt thread. The deviation of the adjacent center distance of the bolts is ≤2, and the deviation of any two spacings is ≤ 3mm; After the welding is completed, hammering and bending are used to check the welding quality of the bolts one by one to ensure that the welding is firm, and then remove the welding slag.

(4) Backing blanket installation

First compress the ceramic fiber blanket to the required thickness, and spread the blanket and blanket in a staggered layer (the staggered amount is not less than the drawing requirements), and the quick card must be clamped to prevent rebound.

(5) Module installation

Take out the ceramic fiber module → screw the guide rod to the small end of the screw → pass the ceramic fiber module along the center hole through the guide rod to the furnace plate → use a special wrench to tighten the nut to the screw → unscrew the guide rod → proceed in sequence Installation of other ceramic fiber modules.

It should be noted that the module installation should follow the principle of first furnace top and then furnace wall, from bottom to top. After installing a row of modules, lay a compensation blanket on the cutting surface of the module (2 layers of 20mm blankets are extruded to a thickness of 25mm), and fix them on the installed module with U-shaped nails.

(6) Modular surface finishing

After the ceramic fiber module is installed, flatten the surface of the module with a wooden board to ensure that the module is squeezed tightly, and the large gaps are tightly filled with compensation blankets.

(7) Curing agent spraying

After the insulation layer is installed, in order to prolong the service life of the insulation cotton and enhance the ability to resist wind erosion and air erosion, a protective layer of curing agent should be sprayed on the surface of the module, with an amount of about 1.5kg/m2.

Q&A

1. What is the classification temperature?

The classification temperature is 1050-1400℃

2. What is the delivery sea port?

SHANGHAI, QINGDAO, TIANJIN or as per your request.

Our unremitting efforts have won the wide recognition of customers and people in the industry, and our 1200 Degree Ceramic Fiber Heater Module is sold well at home and abroad and well-received by the majority of users. Welcome to contact us immediately for future business relationship and mutual success! Based on the solemn commitment of customer satisfaction, we actively expand our business and provide all-round business to customers all over the world.

Hot Tags: ceramic fiber module, China, suppliers, manufacturers, factory, customized, wholesale, cheap, pricelist, low price, free sample, nano ceramic beads heat limit, Sic Heaters, ceramic bearings si3n4 skate, easy to machine alumina bisque ceramic sheets, furnace heating element home depot, Silicon Nitride Tubes